View 81006_1225540.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

revisions ltr description date (yr-mo-da) approved f add peak current to absolute maximum ratings. editorial changes throughout. 92-11-24 m. a. frye g changes in accordance with nor 5962-r144-95. 95-10-20 m. a. frye h make corrections to the switch operation table in 3.3.1. update boilerplate to reflect current requirements. -rrp 03-03-10 r. monnin current cage code 67268 the original first sheet of this drawing has been replaced. rev sheet rev sheet rev status rev h h h h h h h h h h h h of sheets sheet 1 2 3 4 5 6 7 8 9 10 11 12 pmic n/a prepared by gary j. zahn defense supply center columbus standard microcircuit drawing checked by william e. sharp columbus, ohio 43216 http://www.d scc.dla.mil this drawing is available for use by all departments approved by n. a. hauck microcircuit, linear, cmos, high level analog switches with drivers, monolithic silicon and agencies of the department of defense drawing approval date 81-10-01 amsc n/a revision level h size a cage code 14933 81006 sheet 1 of 12 dscc form 2233 apr 97 5962-e243-03 distribution statement a . approved for public releas e; distribution is unlimited.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 2 dscc form 2234 apr 97 1. scope 1.1 scope . this drawing describes device requirements for mil- std-883 compliant, non-jan class level b microcircuits in accordance with mil-prf-38535, appendix a. 1.2 part or identifying number (pin) . the complete pin is as shown in the following example: 81006 01 x x drawing number device type (see 1.2.1) case outline (see 1.2.2) lead finish (see 1.2.3) 1.2.1 device type(s) . the device type(s) identify the circuit function as follows: device type generic number circuit function 01 ih5040, dg5140 one-channel, 75 ohms, spst switch 02 ih5041, dg5141 two-channel, 75 ohms, spst switch 03 ih5042, dg5142 one-channel, 75 ohms, spdt switch 04 ih5043, dg5143 two-channel, 75 ohms, spdt switch 05 ih5044, dg5144 one-channel, 75 ohms, dpst switch 06 ih5045, dg5145 two-channel, 75 ohms, dpst switch 07 ih5046 one-channel, 75 ohms, dpdt switch 08 ih5047 one-channel, 75 ohms, 4pst switch 09 ih5140, hi5040 one-channel, 75 ohms, spst switch 10 ih5141, hi5041 two-channel, 75 ohms, spdt switch 11 ih5142, hi5042 one-channel, 75 ohms, spdt switch 12 ih5143, hi5043 two-channel, 30 ohms, spdt switch 13 ih5144, hi5044 one-channel, 30 ohms, dpst switch 14 ih5145, hi5045 two-channel, 75 ohms, dpst switch 15 hi5046 one-channel, 75 ohms, dpdt switch 16 ih5047, hi5047 one-channel, 75 ohms, 4pst switch 17 hi5046a one-channel, 30 ohms, dpdt switch 18 hi5047a one-channel, 30 ohms, 4pst switch 19 ih5148, hi5048 two-channel, 30 ohms, spst switch 20 ih5149, hi5049 two-channel, 30 ohms, dpst switch 21 ih5150, hi5050 one-channel, 30 ohms, spdt switch 22 ih5151, hi5051 two-channel, 30 ohms, spdt switch 1.2.2 case outline(s) . the case outline(s) are as designated in mil-std-1835 and as follows: outline letter descriptive designator terminals package style a gdfp5-f14 or cdfp6-f14 14 flat pack e gdip1-t16 or cdip2-t16 16 dual-in-line i macy1-x10 10 can 2 cqcc1-n20 20 square leadless chip carrier x cdfp3-f14 14 flat pack 1.2.3 lead finish . the lead finish is as specified in mil-prf-38535, appendix a.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 3 dscc form 2234 apr 97 1.3 absolute maximum ratings . v+ - v- .................................................................................... 33 v dc v+ - v d ................................................................................... 30 v dc v d - v- .................................................................................... 30 v dc v d - v s .................................................................................... 22 v dc v l - v-..................................................................................... 33 v dc v l - v in ................................................................................... 30 v dc v l - v r .................................................................................... 20 v dc v in - v r ................................................................................... 20 v dc v r - v- .................................................................................... 33 v dc v r - v in ................................................................................... 2 v dc current (any terminal except s or d)...................................... 30 ma peak current (source to drain) 1 /........................................... 80 ma storage temperature range .................................................... -65 c to +150 c lead temperature (solder ing, 10 seconds ) ............................ +300 c junction temperature (t j )....................................................... +175 c power dissipation, (p d ) 2 /: cases a and x at t a = +125 c .......................................... 350 mw case e at t a = +125 c ...................................................... 400 mw case i at t a = +125 c ........................................................ 350 mw case 2 at t a = +125 c ....................................................... 350 mw 1.4 recommended operating conditions . +v cc ...................................................................................... +15 v dc -v cc ....................................................................................... -15 v dc v r .......................................................................................... 0 v dc v l .......................................................................................... 5 v dc ambient operating temperature range (t a ) ............................ -55 c to +125 c thermal resistance, junction-to-case ( jc ) ............................. see mil-std-1835 2. applicable documents 2.1 government specification, standards, and handbooks . the following specification, standards, and handbooks form a part of this drawing to the extent specified herein. unless ot herwise specified, the issues of these documents are those liste d in the issue of the department of defens e index of specifications and standards (d odiss) and supplement thereto, cited in the solicitation. specification department of defense mil-prf-38535 -- integrated circuits, manufacturing, general specification for. standards department of defense mil-std-883 - test method standard microcircuits. mil-std-1835 - interface standard electronic component case outlines. 1 / pulse at 1 ms, 10 percent duty cycle maximum. 2 / for t a = +100 c to +125 c, derate linearly at 12 mw/ c.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 4 dscc form 2234 apr 97 handbooks department of defense mil-hdbk-103 -- list of standard microcircuit drawings. mil-hdbk-780 - standard microcircuit drawings. (unless otherwise indicated, copies of the specificat ion, standards, and handbooks are ava ilable from the standardization document order desk, 700 robbins avenue, building 4d, philadelphia, pa 19111-5094.) 2.2 order of precedence . in the event of a conflict between the text of th is drawing and the references cited herein, the text of this drawing takes precedence. nothing in this docum ent, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. requirements 3.1 item requirements . the individual item requirements shall be in accordance with mil-prf-38535, appendix a for non- jan class level b devices and as specified herein. product built to this drawing that is produced by a qualified manufacturer listing (qml) certified and qualified manufacturer or a manufac turer who has been granted transitional certification to mil- prf-38535 may be processed as qml product in accordance wi th the manufacturers approved program plan and qualifying activity approval in accordance with mil-prf-38535. this qml flow as documented in the quality management (qm) plan may make modifications to the requirements herein. these modifi cations shall not affect form, fit, or function of the device. these modifications shall not affect the pin as described herein. a "q" or "qml" certification mark in accordance with mil- prf-38535 is required to identify when the qml flow option is used . 3.2 design, construction, and physical dimensions . the design, construction, and physical dimensions shall be as specified in mil-prf-38535, appendix a and herein. 3.2.1 case outline(s) . the case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 terminal connections . the terminal connections sha ll be as specified on figure 1. 3.3 electrical perfo rmance characteristics . unless otherwise specified herein, the electrical performance characteristics are as specified in table i and shall apply over the full ambient operati ng temperature range. 3.3.1 switch operation . the analog switches listed below are guaranteed to turn ?on? with either a ?low? input (v r v il 0.8 v) or ?high? input (2.4 v v ih v il ) as specified below (see figure 1). device types v in channels on channels off 2.4 v dc 1 01, 09 0.8 v dc 1 2.4 v dc 1, 2 02, 10, 05, 13, 19 0.8 v dc 1, 2 2.4 v dc 1 2 03, 11, 21 0.8 v dc 2 1 2.4 v dc 1, 2 3, 4 04, 12, 22 0.8 v dc 3, 4 1, 2 2.4 v dc 2, 3 1, 4 07, 15, 17 0.8 v dc 1, 4 2, 3 2.4 v dc 1, 2, 3, 4 06, 08, 14, 16, 18, 20 0.8 v dc 1, 2, 3, 4 3.4 electrical test requirements . the electrical test requirements shall be the subgroups specified in t able ii. the electrical tests for each subgroup are described in table i. 3.5 marking . marking shall be in accordance with mil-prf-38535, appendix a. the part shall be marked with the pin listed in 1.2 herein. in addition, the manufacturer's pin may also be marked as listed in mil-hdbk-103 (see 6.6 herein). for packages where marking of the entire smd pin number is not feasible due to space limitati ons, the manufacturer has the option of not marking the "5962-" on the device.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 5 dscc form 2234 apr 97 table i. electrical per formance characteristics . test symbol conditions -55 c t a +125 c v cc = 15 v unless otherwise specified group a subgroups device type limits unit min max 1, 3 75 2 1 - 16 150 1, 3 45 v d = -10 v, i s = 10 ma, 2 17 - 22 50 1, 3 75 2 1 - 16 150 1, 3 45 v d = 10 v, i s = -10 ma, 2 17 - 22 50 1, 3 75 v d = -7.5 v, i s = 10 ma, v cc = 10 v 2 / 2 150 1, 3 75 drain source ?on? resistance r ds v d = 7.5 v, i s = -10 ma, v cc = 10 v 2 / 2 all 150 ? 1 / 2, 3 -200 200 v s = v d = 10 v, see 3.3.1 for v in 1 -2 2 2, 3 -200 200 channel ?on? leakage current i d(on) v s = v d = -10 v, see 3.3.1 for v in 1 all -2 2 na 2, 3 -100 100 v s = -10 v, v d = 10 v, see 3.3.1 for v in 1 -1 1 2, 3 -100 100 drain ?off? leakage current i d(off) v s = 10 v, v d = -10 v, see 3.3.1 for v in 1 all -1 1 na 2, 3 -100 100 v s = 10 v, v d = -10 v, see 3.3.1 for v in 1 -1 1 2, 3 -100 100 source ?off? leakage current i s(off) v s = -10 v, v d = 10 v, see 3.3.1 for v in 1 all -1 1 na 1, 3 -1 1 input current, input voltage low i il v in = 0 v 2 all -10 1 a 1, 3 -1 1 input current, input voltage high i ih v in = 2.4 v, 5 v 2 all -1 10 a 1, 3 10 2 1-8 100 1 200 positive supply current +i cc v in = 0 v, 5 v 2, 3 9 - 22 300 a 1, 3 -10 2 1 - 8 -100 1 -200 negative supply current -i cc v in = 0 v, 5 v 2, 3 9 - 22 -300 a see footnotes at end of table.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 6 dscc form 2234 apr 97 table i. electrical per formance characteristics ? continued. test symbol conditions -55 c t a +125 c v cc = 15 v unless otherwise specified group a subgroups device type limits unit min max 1, 3 10 2 1 - 8 100 1 -200 logic supply current +i l v in = 0 v, 5 v 2, 3 9 - 22 -300 a 1, 3 -10 2 1 - 8 -100 1 -200 reference supply current +i r v in = 0 v, 5 v 2, 3 9 - 22 -300 a 11 375 9 450 10 1 - 8 550 11 450 9 500 turn-on time t on 10 9 - 22 800 ns 11 250 9 250 10 1 - 8 400 11 350 9 450 turn-off time t off 10 9 - 22 600 ns single channel isolation 2 / v iso r l = 100 ? , f = 100 khz, v in = 2 v p-p , c l = 5 pf, t a = +25 c 9 all 60 db crosstalk between channels 2 / v ct r l = 100 ? , f = 100 khz, v in = 2 v p-p , c l = 5 pf, t a = +25 c 9 all 60 db charge transfer error 2 / v cte v in = 0 v, c l = 10 nf, t a = +25 c 9 all 30 mv break before make time delay 2 / t d t a = +25 c 9 03, 04, 07 5 ns driver input capacitance 2 / c a v in = 0 v, t a = +25 c 9 all 45 pf switch input capacitance 2 / c is switch off, t a = +25 c 9 all 60 pf switch output capacitance 2 / c os switch off, t a = +25 c 9 all 60 pf 1 / the listed resistance limits correspond to the following voltage values: 45 ? and 75 ? ? 9.25 v, 6.75 v 50 ? and 150 ? - 8.50 v, 6.0 v 2 / if not tested, shall be guaranteed to t he limits specified in table i herein.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 7 dscc form 2234 apr 97 device type 01 device types 01 and 09 device type 09 only case outline a case outline e case outline i device type 02 device types 02 and 10 device type 19 case outline a case outline e case outline e figure 1. terminal connections .
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 8 dscc form 2234 apr 97 device types 02 and 10 device type 03 device types 03, 11, and 21 case outline i case outline a case outline e device type 04 device types 04, 12, and 22 case outline a case outline e case outline 2 figure 1. terminal connections ? continued.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 9 dscc form 2234 apr 97 device type 05 device types 05 and 13 case outline a case outline e c ase outline i device type 06 device types 06, 14, and 20 case outline a and x case outline e case outline 2 figure 1. terminal connections ? continued.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 10 dscc form 2234 apr 97 device type 07 device types 07, 15, and 17 case outline a cas e outline e device type 08 device types 08, 16, and 18 case outline a cas e outline e figure 1. terminal connections ? continued.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 11 dscc form 2234 apr 97 3.5.1 certification/compliance mark . a compliance indicator ?c? shall be mark ed on all non-jan devices built in compliance to mil-prf-38535, appendix a. the compliance indicator ?c? sha ll be replaced with a "q" or "qml" certification mark in accordance with mil-prf-38535 to identify when the qml flow option is used . 3.6 certificate of compliance . a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in mil-hdbk-103 (s ee 6.6 herein). the certificate of co mpliance submitted to dscc-va prior to listing as an approved source of supply s hall affirm that the manufacturer's pr oduct meets the requirements of mil-prf- 38535, appendix a and the requirements herein. 3.7 certificate of conformance . a certificate of conformance as requi red in mil-prf-38535, appendix a shall be provided with each lot of microcircuits delivered to this drawing. 3.8 notification of change . notification of change to dscc-va shall be required in accordance with mil-prf-38535, appendix a. 3.9 verification and review . dscc, dscc's agent, and the acquiring activity re tain the option to review the manufacturer's facility and applicable required documentation. offshore documentation shall be made av ailable onshore at the option of the reviewer. 4. quality assurance provisions 4.1 sampling and inspection . sampling and inspection procedures sha ll be in accordance with mil-prf-38535, appendix a. 4.2 screening . screening shall be in accordance with method 5004 of mil-std-883, and shall be conducted on all devices prior to quality conformance inspection. the following additional criteria shall apply: a. burn-in test, method 1015 of mil-std-883. (1) test condition a, b, c or d. the test circuit sha ll be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. the test circuit shall specify the inputs, outputs, biases, and pow er dissipation, as applicable, in acco rdance with the intent specified in test method 1015 of mil-std-883. (2) t a = +125 c, minimum. b. interim and final electrical test parameters shall be as spec ified in table ii herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 quality conformance inspection . quality conformance inspection shall be in accordance with method 5005 of mil-std- 883 including groups a, b, c, and d inspections. the following additional criteria shall apply. 4.3.1 group a inspection . a. tests shall be as specified in table ii herein. b. subgroups 4, 5, 6, 7, and 8 in table i, method 5005 of mil-std-883 shall be omitted.
standard microcircuit drawing size a 81006 defense supply center columbus columbus, ohio 43216-5000 revision level h sheet 12 dscc form 2234 apr 97 table ii. electrical test requirements . mil-std-883 test requirements subgroups (in accordance with mil-std-883, method 5005, table i) interim electrical parameters (method 5004) ---- final electrical test parameters (method 5004) 1*, 2, 3 group a test requirements (method 5005) 1, 2, 3, 9, 10, 11 groups c and d end-point electrical parameters (method 5005) 1 * pda applies to subgroup 1. 4.3.2 groups c and d inspections . a. end-point electrical parameters shall be as specified in table ii herein. b. steady-state life test conditions, method 1005 of mil-std-883. (1) test condition a, b, c, or d. the test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the prepari ng or acquiring activity upon request. the test circuit shall specify the inputs, outputs, biases, and power dissi pation, as applicable, in accordance with the intent specified in test method 1005 of mil-std-883. (2) t a = +125 c, minimum. (3) test duration: 1,000 hours, except as permitted by method 1005 of mil-std-883. 5. packaging 5.1 packaging requirements . the requirements for packaging shall be in accordance with mil-prf-38535, appendix a. 6. notes 6.1 intended use . microcircuits conforming to this drawing are intended for use for gove rnment microcircuit applications (original equipment), design applic ations, and logistics purposes. 6.2 replaceability . microcircuits covered by this drawing will repl ace the same generic device covered by a contractor- prepared specification or drawing. 6.3 configuration control of smd's . all proposed changes to existing smd's will be coordinated with the users of record for the individual documents. this coordination will be accomplished using dd form 1692, engineering change proposal. 6.4 record of users . military and industrial users shall inform defens e supply center columbus when a system application requires configuration control and the applicable smd. dscc w ill maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. us ers of drawings covering micr oelectronics devices (fsc 5962) should contact dscc-va, telephone (614) 692-0544. 6.5 comments . comments on this drawing should be directed to dscc-va, columbus, ohio 43216-5000, or telephone (614) 692-0547. 6.6 approved sources of supply . approved sources of supply are listed in mil-hdbk-103. the vendors listed in mil- hdbk-103 have agreed to this drawing and a certificate of co mpliance (see 3.6 herein) has been submitted to and accepted by dscc-va.
standard microcircuit drawing bulletin date: 03-03-10 approved sources of supply for smd 81006 are listed below for immediate acquisition information only and shall be added to mil-hdbk-103 and qml-38535 during the next revisi on. mil-hdbk-103 and qml-38535 will be revised to include the addition or deletion of sources. the vendors lis ted below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by dscc- va. this bulletin is superseded by the next dated revision of mil-hdbk-103 and qml-38535. standard microcircuit drawing pin 1 / vendor cage number vendor similar pin 2 / reference military specification pin 8100601aa 3 / m38510/10501baa 8100601ea 1es66 ih5040mje/883b m38510/10501bea 3 / dg5140ak 8100602aa 3 / m38510/10502baa 8100602ea 1es66 ih5041mje/883b m38510/10502bea 3 / dg5141ak 8100602ia 3 / dg5141aa m38510/10502bia 8100603aa 3 / m38510/10503baa 8100603ea 1es66 ih5042mje/883b m38510/10503bea 3 / dg5142ak 8100604aa 3 / m38510/10504baa 8100604ea 3 / ih5043mje m38510/10504bea 1es66 ih5043mje/883b 3 / dg5143ak 8100605aa 3 / m38510/10505baa 8100605ea 1es66 ih5044mje/883b m38510/10505bea 3 / dg5144ak 8100605ia 3 / dg5144aa m38510/10505bia 8100606aa 3 / ih5045mfd/883b m38510/10506baa 8100606ea 1es66 ih5045mje/883b m38510/10506bea 3 / dg5145ak 8100606xc 1es66 ih5045mfd/883b 8100607aa 3 / m38510/10507baa 8100607ea 3 / m38510/10507bea 8100608aa 3 / m38510/10508baa 8100608ea 1es66 ih5047mje/883b m38510/10508bea 8100609ea 1es66 ih5140mje/883b m38510/10501bea 3 / hi1-5040/883 8100609ia 3 / m38510/10501bia see footnotes at end of table. 1 of 3
standard microcircuit drawing bulletin ? continued. standard microcircuit drawing pin 1 / vendor cage number vendor similar pin 2 / reference military specification pin 8100610ea 1es66 ih5141mje/883b m38510/10502bea 3 / ih5141mje 34371 hi1-5041/883 8100610ia 3 / m38510/10502bia 8100611ea 1es66 ih5142mje/883b m38510/10503bea 3 / ih5142mje 34371 hi1-5042/883 8100612ea 1es66 ih5143mje/883b m38510/10504bea 3 / ih5143mje 34371 hi1-5043/883 81006122a 34371 hi4-5043/883 --- 8100613ea 1es66 ih5144mje/883b m38510/10505bea 3 / ih5144mje 3 / hi1-5044/883 8100613ia 3 / m38510/10505bia 8100614ea 1es66 ih5145mje/883b m38510/10506bea 3 / ih5145mje 3 / hi1-5045/883 81006142a 3 / hi4-5045/883 --- 8100615ea 3 / hi1-5046/883 m38510/10507bea 8100616ea 1es66 ih5047mje/883b m38510/10508bea 3 / hi1-5047/883 8100617ea 34371 hi1-5046a/883 --- 8100618ea 3 / hi1-5047a/883 --- 8100619ea 3 / ih5148mje/883b --- 3 / hi1-5048/883 see footnotes at end of table. 2 of 3
standard microcircuit drawing bulletin ? continued. standard microcircuit drawing pin 1 / vendor cage number vendor similar pin 2 / reference military specification pin 8100620ea 1es66 ih5149mje/883b --- 3 / hi1-5049/883 81006202a 3 / hi4-5049/883 --- 8100621ea 1es66 ih5150mje/883b --- 3 / hi1-5050/883 8100622ea 3 / ih5151mje --- 34371 hi1-5051/883 1es66 ih5151mje/883b 81006222a 34371 hi4-5051/883 --- 1 / the lead finish shown for each pin representing a hermetic package is the most readily available from the manufacturer listed for that part. if the desired lead finish is not listed contact the vendor to determine its availability. 2 / caution . do not use this number for item acquisition. items acquired to this number may not satisfy the performance requirements of this drawing. 3 / not available from an approved source of supply. vendor cage vendor name number and address 1es66 maxim integrated products 120 san gabriel drive sunnyvale, ca 94086 34371 intersil corporation 2401 palm bay blvd p.o. box 883 melbourne, fl 32902-0883 the information contained herein is disseminated for convenience only and the government assumes no liability whatsoever for any inaccuracies in the information bulletin. 3 of 3

▲Up To Search▲

Price & Availability of 81006

	To Download 81006 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .